Light Type Slewing Ring Bearing with Internal Gear for Excavator
Slewing bearing is widely used in construction machinery, especially excavator. The feature of excavator turntable bearing is with hardened inner gear and the common diameter ranges from 1m-2m.
At a glance: six steps to save slewing ring bearings
More than 96% of slewing ring failure could be avoided by following simple maintenance tips.
Grease regularly.
Apply a liberal shot of extreme-pressure grease to the fittings around the bearing's circumference at intervals recommended in the operator's manual.
Purge with grease.
Pump grease into the bearing until you see old grease squeeze past the seal. Purged grease can help carry any contaminants out of the bearing.
Inspect the grease.
Rub some of the purged grease between your thumb and forefinger. If you see or feel grit or metal chips in it, there may be a bearing problem.
Honor load charts.
Even slight overloads can dimple the bearing race. One 1/1000 of an inch depression will worsen with subsequent loads and cause eventual failure.
Avoid repetitive, heavy loads.
Lifting with the boom and undercarriage in the same position, such as repetitive curbside digging with an excavator, can put a dimple in the bearing race close to the uneven load. If possible, change the angle of approach from job to job.
Wire-race slewing rings are known for being very light and reliable. They're used in medical scanning equipment and radar antennas, and are appropriate where lightweight, replaceable raceways or ring material selection is an important consideration. However, self-selection is not recommended; manufacturers should be involved in the design process for slewing rings.
Listed raceway capacities are often static ratings. Since most large-diameter ring applications involve intermittent slewing and a broad spectrum of loads, it's prudent to select a ring based on its static capacity — and a recommended application service factor. Capacities listed are non-simultaneous: In other words, a catalog thrust capacity doesn't account for moment or radial loading. Similarly, moment capacity assumes no thrust or radial load, and listed radial capacity accounts for no thrust or moment. When applications involve a load combination, the load components must be combined into an equivalent load. (For static raceway calculations, this equivalent load is taken to be load as seen by the highest loaded rolling element.)
The exact machine duty cycle and the mounting structure design have tremendous influence on the durability of the ring. In high-cycle applications, dynamic capacity, rather than static capacity, may dominate the slewing ring selection.
If you have any question or enquiry ,pls feel free to contact us.
Model | Dimensions(mm) | Mounting dimension(mm) | |||||||
D | de | H | D1 | D2 | n | Φ | M | t | |
WD-062.20.0414 | 486 | 326.5 | 56 | 460 | 375 | 24 | 13.5 | 12 | 20 |
WD-062.20.0544 | 616 | 445.2 | 56 | 590 | 505 | 32 | 13.5 | 12 | 20 |
WD-062.20.0644 | 716 | 574.2 | 56 | 690 | 605 | 36 | 13.5 | 12 | 20 |
WD-062.20.0744 | 816 | 649.2 | 56 | 790 | 705 | 40 | 13.5 | 12 | 20 |
WD-062.20.0844 | 916 | 737.6 | 56 | 890 | 805 | 40 | 13.5 | 12 | 20 |
WD-062.20.0944 | 1016 | 841.6 | 56 | 990 | 905 | 44 | 13.5 | 12 | 20 |
WD-062.20.1094 | 1166 | 985.6 | 56 | 1140 | 1055 | 48 | 13.5 | 12 | 20 |
Manufacturing top quality and reliable performance light type slewing bearings in China, Wanda is one of the well-known light type slewing bearings manufacturers. We have professional factory at your service, you can rest assured to order products with our supplier.